CST BLOG: Lab Expectations

The official blog of Cell Signaling Technology (CST) where we discuss what to expect from your time at the bench, share tips, tricks, and information.

Myth-busting for ChIP/ChIP-seq: Using Mono vs Polyclonal Antibodies

Read More
All Posts

Researchers who run a lot of chromatin immunoprecipitation "ChIP" assays—maybe even your advisor—might subscribe to the idea that polyclonal antibodies perform better than monoclonal antibodies. But is that always actually true?

It’s worth your time to understand the differences between the two in terms of antigen recognition and specificity, and dispel some myths. 

Monoclonal and Polyclonal Antibodies for Chromatin Immunoprecipitation

18-CHP-27936 Blog- ChIP experiment Abs- mono vs poly 800x400Monoclonal antibodies that have been properly validated will recognize only a single epitope of an antigen and are extremely specific. Polyclonal antibodies, on the other hand, recognize multiple epitopes of an antigen. They’re a mixture of antibodies. Sometimes polyclonals are the only choice, for example when a hot new target is under investigation, and there hasn’t been enough time to produce and validate a monoclonal. But much of the time, you’ll have a choice to make—mono vs. poly.

New to ChIP? Not sure where to start? Read the tale of one scientist's journey from ChIP novice to ChIP master: Keep CHiP'ing Away.

One of the perceptions about polyclonal antibodies is that the recognition of multiple epitopes improves the chances of pulling down the target protein in ChIP when epitope accessibility is a concern. In reality, this is the case only if a recombinant, full-length protein was used to generate the poly. Many polyclonal antibodies for ChIP (particularly modification state-specific antibodies) are generated against peptide antigens that are only 20-40 amino acids long. This means fewer epitopes than you might expect, and the epitopes are likely to overlap with each other. In short, you’re not likely to receive the benefits of “multiple epitopes”.

Can you afford antibody lot-to-lot variability?

There’s another crucial consideration for all polyclonal antibodies: there is a chance that one or more species in the polyclonal mixture will cross-react with off-target proteins, leading to background signal. When testing a polyclonal antibody, you might find that the background is acceptably low. However, the problem with polyclonals is that the molar ratio of individual antibody species, and hence the overall specificity of the polyclonal mixture, will vary from one lot to another. Consider each polyclonal antibody lot to be a limited resource, because the next lot may have different performance characteristics.

Lot-to-lot variability has implications for your work. Your paper might get published in a year, but then for the follow-up study the following year, you might be forced to switch to a new lot of polyclonal and get the unpleasant surprise that it doesn't work anymore. ("Oh, ChIP!")

Additional resources: CST ChIP Protocols 

There is good news, however. Thanks to their, well, monoclonality, monoclonal antibodies offer much more consistent lot-to-lot specificity. This is applicable to ChIP experiments as well as other applications. And unlike polyclonal lots, monoclonals (including recombinant rabbit mAbs) are renewable resources.

Head-to-Head (ChIP-to-ChIP?) Comparison of Mono vs Poly Antibodies

In a recent paper published in Epigenetics & Chromatin, investigators at the Broad Institute performed a systematic investigation to compare mono vs poly antibody performance in ChIP-seq. Four key histone modifications were selected for analysis. The performance of monoclonal antibodies was highly correlated with that of polyclonals for both genome-wide and region-specific read counts, and the authors concluded that monoclonals could substitute for widely-used polyclonals and improve reliability (for the reasons of consistency and renewability mentioned above) and simplify interpretation of ChIP-seq datasets.

Bear in mind that consistency and renewability are valuable only if the antibody has been validated. Antibodies made at CST are rigorously validated across applications including ChIP. Their specificity is tested using relevant methods and model systems, including but not limited to, inhibitor/activator treatment to modulate upstream signaling; negative, positive, and overexpressing cell lines; and genetically manipulated knockout/knockdown cell lines. It’s not surprising, then, that the most popular CST reagents for ChIP and ChIP-seq are recombinant monoclonal antibodies.  

Want to find out how our tools stack up? See more head-to-head performance comparisons performed in ChIP and ChIP-seq here:

ChIP/ChIPseq  Performance Comparison

 

Kenneth Buck, PhD
Kenneth Buck, PhD
A cell biologist by training, Ken received a PhD at Rutgers and continued as a postdoctoral fellow at Yale, where he studied cytoskeletal dynamics and signaling mechanisms involved in the cellular motility of regenerating neurons. At CST, Ken collaborates with scientists to create multimedia scientific communications. When he's not writing video scripts or in the studio, he can be observed in his natural habitat, mountain biking with colleagues on the rocky North Shore of Massachusetts.

Related Posts

Employee-Directed Global Giving Provides $150K for Humanitarian Causes

At Cell Signaling Technology (CST), our philosophy of giving and supporting those in need is at the heart...
Krystyna Hincman Mar 20, 2024

Five Reasons to Choose a Conjugation Service Over an Antibody Labeling Kit

The need for antibody conjugation is on the rise due to the increased use of multiplexing. Not only are e...
Alexandra Foley Mar 6, 2024

Networking at Conferences: Five Tips for the Introverted Scientist

Networking is an important part of any research career,1 with many experts considering networking and net...
Kenneth Buck, PhD Feb 28, 2024